Jump to content
Ad: Genuine BMW parts & accessories from the BMW official store on eBay ×

Steering sensor fault

Johnoc

By Johnoc,
in BMW X5 Series Forum

 Share

Recommended Posts

Johnoc Rookie

Johnoc

Posted
Posted

Hi. I have plugged in my scanner and when I go into the steering angle sensor information I am getting no change in the degree of steering angle when I'm turning the wheel. I was getting a reading of 727 degrees and no rotation rate.
I cleared the steering angle sensor fault code and calibrated the steering angle sensor and the DSC light goes off. If I turn the car off and leave it for 5 mins the light is back on when I start the car. Can anyone clarify it it's a faulty steering angle sensor
Thanks

CA063FF8-07D0-4035-B136-A15123580BDC.jpeg

Greydog Grand Master

Greydog

Posted
Posted

Morning John

Welcome to the Forum

The Steering Angle sensor is one of the few issues I have not had to deal with, I take it you have cleaned all the connectors/plugs with contact cleaner just in case it is a gungy joint that has a continuity failure when the system self tests at ignition on? Check www.newtis.info for BMW's test and check information.

I have read about a few folks that have had to change the sensor and there are how too's on You Tube and the Pelikan parts website (US site but good info) 

Dave

 

Johnoc Rookie

Johnoc

Posted
  • Author
Posted
2 minutes ago, Greydog said:

Morning John

Welcome to the Forum

The Steering Angle sensor is one of the few issues I have not had to deal with, I take it you have cleaned all the connectors/plugs with contact cleaner just in case it is a gungy joint that has a continuity failure when the system self tests at ignition on? Check www.newtis.info for BMW's test and check information.

I have read about a few folks that have had to change the sensor and there are how too's on You Tube and the Pelikan parts website (US site but good info) 

Dave

 

hi Dave,

thanks for the advise. i will check connections. it seems strange that i am getting no voltage reading or rotation rate. i presumed as soon as i moved the wheel i should see some changes to angle, rotation rate or voltage.

john 

Greydog Grand Master

Greydog

Posted
Posted

Hi john

www.newtis.info is a BMW technical information site as used by BMW Dealers so that should give all the information your looking for regarding tests and expected results

Dave

Latest Deals

BMW Official Store for genuine BMW parts & accessories

Disclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via eBay links

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing




  • Latest Topics

    1. 7

      105C thermostat replacement

      As I understand the wiring diagrams and operation Item 9 on the thermostat housing is the sensor which sends its signal to the ECU for interpretation with information from the map sensor. Information from item 12 (1st drawing ) is also used to provide average temp across the cooling system. As far as I am aware the Thermostst is independent of the sensors and operated by expanding wax material internally
      Greydog in BMW 7 Series Forum
    2. 13

      BMW 318i boot locked can’t get into

      Errr not clear here Donald Plastic "L's" with short rubber hoses ??? Distilled water/Ionised water should only be used in an old style lead acid battery. The Rad and engine coolining system should be filled with the correct coolant mix to prevent cavitation and the danger of freezing in low temps. Coolant should be part of the cars regular maintenance and changed every 3 years or so. At that time all hoses and connectors should be inspected and changed where necessary to keep everything in tip top condition. Changing parts can cause as many problems as you may think your solving
      Greydog in BMW 3 Series Forum
    3. 13

      BMW 318i boot locked can’t get into

      Update: I checked my battery and it charged in 5 minutes, so I don't have to find another alternator. All seems to be OK except for the plastic "L"s with a short rubber hose that bypass the HV/AC solenoid. Those get clogged after @ 150,000-190,000 miles (if distilled water wasn't used) and cause air pockets that try to burst radiators. I have a few more brass "L"s, so now I can throw the plastic ones away. I have to be careful I don't fog the windows though, without heat or cool.
      DDONNY in BMW 3 Series Forum
    4. 7

      105C thermostat replacement

      You are absolutely right. The strange thing is that when I put the chassis number on the realoem it shows that the temp sensor is not applicable on my vehicle. I will physically check for a sensor. In the meantime, do you think that the removal of the MAP activated thermostat will effect the temp gauge on the dial instrument item 6? I am tempted to add a dummy resistor , 11.5ohms - 13watts , to simulate the MAP thermostat. Your thoughts?
      Dimitris in BMW 7 Series Forum
    5. 14

      X5 e53 reverse sensors video required please

      What's Brazillian for BIG THUD 🤣🤣 Dave
      Greydog in BMW X5 Series Forum

  • Recent Achievements

    • Week One Done
      Karlos70
      Karlos70 earned a badge
      Week One Done
    • Week One Done
      DDONNY
      DDONNY earned a badge
      Week One Done
    • Collaborator
      Dimitris
      Dimitris earned a badge
      Collaborator
    • Week One Done
      DAW90
      DAW90 earned a badge
      Week One Done
    • First Post
      jn1253
      jn1253 earned a badge
      First Post

×
×
  • Create New...

Forums

News

Membership