Jump to content
Ad: Genuine BMW parts & accessories from the BMW official store on eBay ×

BMW E21 320 1982 not ticking over

Peter Parr

By Peter Parr,
in BMW Classics Forum

 Share

Recommended Posts

Peter Parr Newbie

Peter Parr

Posted
Posted

My BMW E21 320 1982 is not used a lot. It runs but won't tick over unless I keep it revving. Have completely rebuilt the carburettor and a new automatic choke unit has been fitted but it still needs to be continually revved. If you take your foot off the accelerator the car just dies. Any suggestions?

Greydog Grand Master

Greydog

Posted
Posted

If I recall there is an Electric Idle valve on the carb has this been rebuilt? From memory there was a diaphragm that used to need replacing when the idle went wonky.

Hope this helps

Dave

Latest Deals

BMW Official Store for genuine BMW parts & accessories

Disclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via eBay links

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing




  • Latest Topics

    1. 6

      105C thermostat replacement

      You are absolutely right. The strange thing is that when I put the chassis number on the realoem it shows that the temp sensor is not applicable on my vehicle. I will physically check for a sensor. In the meantime, do you think that the removal of the MAP activated thermostat will effect the temp gauge on the dial instrument item 6? I am tempted to add a dummy resistor , 11.5ohms - 13watts , to simulate the MAP thermostat. Your thoughts?
      Dimitris in BMW 7 Series Forum
    2. 14

      X5 e53 reverse sensors video required please

      What's Brazillian for BIG THUD 🤣🤣 Dave
      Greydog in BMW X5 Series Forum
    3. 13

      SLIPPING CLUTCH

      Morning Andrew I normally disconnect the Neg lead only, some folks disconnect both a few even say disconnect both and touch them together. Goes without saying both sensor plugs need to be checked and a squirt of contact cleaner applied never hurts 😅 Dave
      Greydog in BMW 5 Series Forum
    4. 13

      SLIPPING CLUTCH

      Hi Dave, I fitted one of the sensors on the rear but it has made no effect as the light is still there, I will fit the other sensor tomorrow and see how it goes then. You mention the disconnect the battery, is there any pattern to this ? is it both leads or just the negative lead? cheers Paneuro.
      paneuro in BMW 5 Series Forum
    5. 6

      105C thermostat replacement

      Not sure what engine your running but there should be a Temp sensor in the Hose from the Rad to the water pump then there should be a Temp sensor in the housing for the Thermostat Both are shown in realoem for the 3.5 V8 I thought the V8 was the only one with dual use sensor on the Thermostat housing but stand to be corrected Dave
      Greydog in BMW 7 Series Forum

  • Recent Achievements

    • Collaborator
      Dimitris
      Dimitris earned a badge
      Collaborator
    • Week One Done
      DAW90
      DAW90 earned a badge
      Week One Done
    • First Post
      jn1253
      jn1253 earned a badge
      First Post
    • Conversation Starter
      BMW X3 3.0L timing issues
      BMW X3 3.0L timing issues earned a badge
      Conversation Starter
    • First Post
      Wayne1001
      Wayne1001 earned a badge
      First Post

×
×
  • Create New...

Forums

News

Membership