Jump to content
Ad: Genuine BMW parts & accessories from the BMW official store on eBay ×

Handbrake help needed.

Michael Middleton

By Michael Middleton,
in BMW 1 Series Forum

 Share

Recommended Posts

Michael Middleton Rookie

Michael Middleton

Posted
Posted

Hi everyone. I have a 2011 BMW 1 series, and am having slight issues with the handbrake. When I release the handbrake, sometimes (not every time) the car will still think the handbrake is up and the warning light will come on on the dash. It will not turn off unless I tap or hit the handbrake downwards; This seems to make the car think the handbrake is finally released fully. Any help / suggestions would be greatly appreciated 

Greydog Grand Master

Greydog

Posted
Posted

Morning Michael

Welcome to the Forum

It sounds as though the hand brake switch is sticking or loose, it should be located under the centre consul at the back of the hand brake.

Some contact cleaner may solve the problem

Dave

  • Like 1

Latest Deals

BMW Official Store for genuine BMW parts & accessories

Disclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via eBay links

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing




  • Latest Topics

    1. 6

      105C thermostat replacement

      You are absolutely right. The strange thing is that when I put the chassis number on the realoem it shows that the temp sensor is not applicable on my vehicle. I will physically check for a sensor. In the meantime, do you think that the removal of the MAP activated thermostat will effect the temp gauge on the dial instrument item 6? I am tempted to add a dummy resistor , 11.5ohms - 13watts , to simulate the MAP thermostat. Your thoughts?
      Dimitris in BMW 7 Series Forum
    2. 14

      X5 e53 reverse sensors video required please

      What's Brazillian for BIG THUD 🤣🤣 Dave
      Greydog in BMW X5 Series Forum
    3. 13

      SLIPPING CLUTCH

      Morning Andrew I normally disconnect the Neg lead only, some folks disconnect both a few even say disconnect both and touch them together. Goes without saying both sensor plugs need to be checked and a squirt of contact cleaner applied never hurts 😅 Dave
      Greydog in BMW 5 Series Forum
    4. 13

      SLIPPING CLUTCH

      Hi Dave, I fitted one of the sensors on the rear but it has made no effect as the light is still there, I will fit the other sensor tomorrow and see how it goes then. You mention the disconnect the battery, is there any pattern to this ? is it both leads or just the negative lead? cheers Paneuro.
      paneuro in BMW 5 Series Forum
    5. 6

      105C thermostat replacement

      Not sure what engine your running but there should be a Temp sensor in the Hose from the Rad to the water pump then there should be a Temp sensor in the housing for the Thermostat Both are shown in realoem for the 3.5 V8 I thought the V8 was the only one with dual use sensor on the Thermostat housing but stand to be corrected Dave
      Greydog in BMW 7 Series Forum

  • Recent Achievements

    • Collaborator
      Dimitris
      Dimitris earned a badge
      Collaborator
    • Week One Done
      DAW90
      DAW90 earned a badge
      Week One Done
    • First Post
      jn1253
      jn1253 earned a badge
      First Post
    • Conversation Starter
      BMW X3 3.0L timing issues
      BMW X3 3.0L timing issues earned a badge
      Conversation Starter
    • First Post
      Wayne1001
      Wayne1001 earned a badge
      First Post

×
×
  • Create New...

Forums

News

Membership