Jump to content
Ad: Genuine BMW parts & accessories from the BMW official store on eBay ×

BMW 1 Series 2011 Convert, rear near side wheel arch trim

kooge0

By kooge0,
in BMW 1 Series Forum

 Share

Recommended Posts

kooge0 Rookie

kooge0

Posted
Posted

Hi

I have found that the trim is loose, and has no fixings in the points 11 & 13 detailed below..........just blank holes fixed to fresh air behind 😞

I am struggling to locate a diagram that details how/where points 11 & 13 fix too........if at all??

The other side is absolutely solid 😞

Please can someone advise.

Many thanks

 

BMW Genuine Rear Left NS Wheel Housing Cover Fits F32 F32 LCI F33 51717260747 - Picture 1 of 5

  • 3 weeks later...
kooge0 Rookie

kooge0

Posted
  • Author
Posted

Hi All

I spoke to the local authorized BMW Colchester dealer, and advised car reg number + full details of the issue.

I was amazed at the lack of assistance/knowledge 😬

I explained that I was attempting to trace the actual part/s that the push fit rivets (No 11 & 13) attached too. I explained that my car has 'fresh air' behind the No 2 wheel arch, only open mounting holes.

All I got was "you have to know what you are after" (and was presented with the same drawing as above).............my reply "that's the problem, whatever was supposed to be there is missing......how am I supposed to know what was there in the first place.......if at all"

Does anyone have a BMW Series 1 E88 Convertible 2011, who can assist in resolving the mystery............a photo would be a life saver 😁

Latest Deals

BMW Official Store for genuine BMW parts & accessories

Disclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via eBay links

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing




  • Latest Topics

    1. 2

      Connectors in the boot next to the battery

      Hi Dave - Thank you got the excellent advice and information. Could you tell me where the main fuse box is (never had a BMW before)? We have a friend coming over to scan the car on Thursday so hopefully sort out the issues or at least know what to fix first. Thanks once again - Kind regards Andrew
      Andrewkuk in BMW 1 Series Forum
    2. 2

      Connectors in the boot next to the battery

      Morning Andrew Welcome to the Forum looks like your missing a module rear camera or PDC could be a Towing Module Not sure about BCM (I assume this is Body Control Module?) BMW 1.4.0 or ISTA/INPA should/normally show Greyed out Modules as not communicating allowing indentification of Failed units The Footwell Control Module was a common issue on several models and a simple change whether you go new or recycled it will cause a Tamper Dot by the mileage, so your new unit will need to be registered to your chassis and the mileage matched to your car. Junction Box Electroncs is the next biggy mainly due to where it is situated. Dont forget check or better still change the Fuel Pump Relay one of the common faults Also disconnect the modules check the connectors for signs of corrosion on pins give every thing a clean and spray of electrical contact cleaner and put it back. I have fixed several this way. Good Luck Dave
      Greydog in BMW 1 Series Forum
    3. 1

      Z3 airbag wiring,

      Hi. Do you have a light on the dash? It could be that someone fitted an emulator ?
      X5smw in BMW Z3 & Z4 Series Forum
    4. 1

      Z3 airbag wiring,

      I'm am sorry if I am doing this incorrectly but I have searched and not found anything related to this but I am still learning all of this. Does anyone know about the yellow airbag/ seat belt connector under the driver’s seat? I am sure the previous owner has changed this but I am wondering if anyone has seen this before? If so, should I remove the butt connectors and solder the wires? Should the wires be twisted all the way to the yellow connector? Any help is greatly appreciated. Thanks, JayMe
      JayMe in BMW Z3 & Z4 Series Forum
    5. 2

      Connectors in the boot next to the battery

      Hi - I have a 2007 1.6L Petrol 1 series and it has wire connectors in the boot near the battery but I don't know what they are meant to connect to. Are they just spare or is there a part missing? The car currently not starting but we think it is a BCM fault but just wanted to know what the cables in the boot are meant for. Any help would be greatly appreciated be gratefully appreciated as we can't read the fault codes as we think the BCM is faulty and the car won't idle properly but there might be some other issue. Regards Andrew
      Andrewkuk in BMW 1 Series Forum

  • Recent Achievements

    • First Post
      Andrewkuk
      Andrewkuk earned a badge
      First Post
    • Conversation Starter
      JayMe
      JayMe earned a badge
      Conversation Starter
    • Conversation Starter
      Andrewkuk
      Andrewkuk earned a badge
      Conversation Starter
    • One Month Later
      DAW90
      DAW90 earned a badge
      One Month Later
    • First Post
      Max123
      Max123 earned a badge
      First Post

×
×
  • Create New...

Forums

News

Membership