Jump to content
Ad: Genuine BMW parts & accessories from the BMW official store on eBay ×

Bmw No Hot Air Inside

copey-330

By copey-330,
in BMW 3 Series Forum

 Share

Recommended Posts

copey-330 Rookie

copey-330

Posted
Posted

Hi people I need a bit of help if poss cut a long story short I have a BMW 328 e46 1999 now the water pump went down the shoot so instead of going to my local BMW dealer I£££££ I decided to going with after market sort £18 fitted and bleed the system (god knows how many times) but I don't seem to be getting any hot air heating was working fine before I changed the pump so I took the pump back out to check its the same and it looks different its metal on the end and the BMW pump is plastic could this be my problem

G4VHD Grand Master

G4VHD

Posted
Posted

Is it the fins that are metal, if so, thats the better one as the plastic ones are known to snap.

BMW's are a nightmare to bleed!!

G4VHD Grand Master

G4VHD

Posted
Posted

Also, while you in there, get the thermostat and water temp sensor changed.

I'll bet my life there is still air in the system though

copey-330 Rookie

copey-330

Posted
  • Author
Posted

Is it the fins that are metal, if so, thats the better one as the plastic ones are known to snap.

BMW's are a nightmare to bleed!!

Your right there must done the bleed about 5 times , I thought I sorted it before as when I put the water pump back in it got hot and stayed hot Evan when driving until I came to a junction and stopped it became cold again , and back to the water pump the whole end is metal Evan the fins

Snypa-D Grand Master

Snypa-D

Posted
Posted

Metal fins def the better pump,as for the airlock.....good luck with that !! BMW airlock is a flippin nightmare to get rid of,jack the front end up/drive up a ramp etc take of the rad cap/bleed valve and run it till it gets hot and water NOT AIR comes out of it.then it should be done :) good luck

copey-330 Rookie

copey-330

Posted
  • Author
Posted

Metal fins def the better pump,as for the airlock.....good luck with that !! BMW airlock is a flippin nightmare to get rid of,jack the front end up/drive up a ramp etc take of the rad cap/bleed valve and run it till it gets hot and water NOT AIR comes out of it.then it should be done :) good luck

Just seems wired how this has happened since changing the pump , I take it it only has one bleed screw

Latest Deals

BMW Official Store for genuine BMW parts & accessories

Disclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via eBay links

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing




  • Latest Topics

    1. 6

      X3 2.0 automatic

      Many thanks for the help I've hot the car booked in for a full health check but it seem that the transfer box oil as not been changed for nearly 3 years so I'm hoing to do that first to see if it helps
      Davesally in BMW X3 Series Forum
    2. 6

      X3 2.0 automatic

      hi , I had very similar problem a while back, and after a lot of testing with vista, it turned out to be a front R/H wheel , speed/wheel sensor. when it all was happing lots of codes were coming up gearbox, diff front and back, transever box,plus many more, didn't look good, but there was one code that repeatedly came up at the top of the list, at this point it was becoming undriveable ,it just didn't seem that a wheel sensor could cause all these codes. So I went got two wheel speed sensor, replaced driver side front, the problem never came back, the sensor controls so many systems ,cleared all codes, happy days, I could have pulled the car apart for nothing, and got nowhere, except an empty wallet. hope this helps you or someone.
      ANDYORAC in BMW X3 Series Forum
    3. 0

      Water leak at sharkfin aerial

      Has anybody experienced water leakage passed the sharkfin aerial to roof joint face.
      VFullard in BMW 4 Series Forum
    4. 7

      105C thermostat replacement

      As I understand the wiring diagrams and operation Item 9 on the thermostat housing is the sensor which sends its signal to the ECU for interpretation with information from the map sensor. Information from item 12 (1st drawing ) is also used to provide average temp across the cooling system. As far as I am aware the Thermostst is independent of the sensors and operated by expanding wax material internally
      Greydog in BMW 7 Series Forum
    5. 13

      BMW 318i boot locked can’t get into

      Errr not clear here Donald Plastic "L's" with short rubber hoses ??? Distilled water/Ionised water should only be used in an old style lead acid battery. The Rad and engine coolining system should be filled with the correct coolant mix to prevent cavitation and the danger of freezing in low temps. Coolant should be part of the cars regular maintenance and changed every 3 years or so. At that time all hoses and connectors should be inspected and changed where necessary to keep everything in tip top condition. Changing parts can cause as many problems as you may think your solving
      Greydog in BMW 3 Series Forum

  • Recent Achievements

    • Week One Done
      Davesally
      Davesally earned a badge
      Week One Done
    • One Year In
      Backmarker
      Backmarker earned a badge
      One Year In
    • Week One Done
      Karlos70
      Karlos70 earned a badge
      Week One Done
    • Week One Done
      DDONNY
      DDONNY earned a badge
      Week One Done
    • Collaborator
      Dimitris
      Dimitris earned a badge
      Collaborator

×
×
  • Create New...

Forums

News

Membership